Visible frame
Sliding pocket doors
Find your solution
The visible frame kit for Enigma fire rated pocket doors is for use with architraves. The frames are manufactured from solid hardwood steamed beech with a density of 720kg/m3 and is a fully FSC certified.
As standard, the timber door frame is provided to you pre-primed ready, meaning on-site painting in your chosen finish and colour can happen at once. Moreover, the frame can be constructed in differing species of timber and with different finishes, at your request. No architraves are included with the timber frame.
The Enigma pocket door system requires a simple wall build-up:
› 94mm stud
› 1 layer 12.5mm plasterboard either side
The sliding pocket door’s strike jamb comes with rubber batwing seals to provide a seal when the door is closed, ensuring that drafts are kept out.
The leading edge jamb of the Enigma pocket door system is the leading support of the pocket which has a side flange for the plasterboard to butt up against.
The intermediate jamb forms the rest of the pocket for the pocket doors. The aluminium profile has a timber insert which provides extra strength and facilitates easy fixing.
The head channel for the Enigma pocket doors is the same width as the stud, making it simple to accurately place and fix to the head stud.
The leading edge and intermediate jambs slot into the base channel of the Enigma pocket door system and are fixed into place.
Manufactured by GEZE, the gear sets used in the Enigma pocket door system require almost no maintenance and are virtually silent, meaning doors slide open and closed without the difficulties sometimes caused by traditional hinges.
The standard sliding gear set is surface-mounted onto the top of the sliding door and is tested to EN 1527 1998 to 100,000 cycles.
The Enigma pocket door kit is constructed from aluminium. This material can be cut-to-size very simply using a standard carpenters chop saw to tailor to your specific size requirements.
The leading edge and intermediate jambs are slotted into the head channel and fixed into place once plumb.
The Enigma doorset has been acoustically tested and can be provided with the following ratings:
› 24dB
› 28dB
› 30dB
Please contact us on 020 3880 0339 where our Project Consultants would be glad to advise you further.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
574mm – 900mm ES 01
574mm – 900mm (Concealed NFR) ES 01C
900mm – 1290mm ES 02
900mm – 1290mm (Concealed NFR) ES 02C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
784mm – 1290mm ES 03
784mm – 1290mm (Concealed NFR) ES 03C
1290mm – 1450mm ES 04
1290mm – 1450mm (Concealed NFR) ES 04C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
The Enigma pocket door leaf can be ejected from the pocket quickly and easily thanks to the innovative Enigma touch latch with a single push of one leaf.
Order codes
130N Touch latch TL130
Virtually silent operation for use with double doors, when one leaf is activated the other follows suit in a seamless fashion.
In situations where you can’t fit the head of the pocket door directly to the building ceilings or floor slab and deflection tolerance is required, the Enigma system can be supplied with a self supporting head beam. This enables the head to be fitted, supporting up to 120kg.
If your door closes against a wall perpendicular to the door itself, a perpendicular wall jamb profile is provided to do away with the need to have a protruding nib.
The Enigma is fitted with a remote stop as standard, which allows you to adjust the back stop of the pocket door kit once the plasterboard is complete and the door leaf has been installed.
The head of the pocket door kit with track packed down, sits flush with the ceiling.
The Enigma pocket door system can be provided with an automated self closer. The closer is provided with infinite adjustment providing an extremely user friendly experience.
Satin stainless steel
Product code: ELS01
Satin stainless steel
60mm square – SFP01
Satin stainless steel
70mm diameter – CFP01
Satin stainless steel
135mm long – OFP01
Satin stainless steel
135mm long – RFP01
For complete freedom and the flexibility to integrate with any design scheme, the Enigma pocket door system can be ordered with or without a door leaf.
All Enigma door leafs are manufactured to the required size using a solid timber core with hardwood lippings on all 4 sides.
Once constructed, the doors are given cut-outs for sliding gear and (where required) a bottom guide channel so that they arrive on-site in a ‘ready to fit’ form.
For doors wider than 1220mm the door will be supplied in 2 sections to achieve the width. A jointing section will be supplied and a neat 3x3mm shadow gap.
As standard Enigma pocket doors are primed and ready to be painted on site.
A full range of RAL colours can be selected for the door leafs.
Extra durability can be added to the sliding pocket doors with a laminate coating.
If the design requires a veneer, choose from any timber style – it is then lacquered in a sheen of 30%.
The visible frame kit for Enigma fire rated pocket doors is for use with architraves. The frames are manufactured from solid hardwood steamed beech with a density of 720kg/m3 and is a fully FSC certified.
As standard, the timber door frame is provided to you pre-primed ready, meaning on-site painting in your chosen finish and colour can happen at once. Moreover, the frame can be constructed in differing species of timber and with different finishes, at your request. No architraves are included with the timber frame.
The Enigma pocket door system requires a simple wall build-up:
› 94mm stud
› 1 layer 12.5mm plasterboard either side
The doorset’s strike jamb comes with rubber batwing seals to provide a seal when the door is closed.
Timber profiles are provided machined to accept intumescent seals. These are then overclad with the metal trims which are plastered up to conceal the frame.
The leading edge jamb of the Enigma pocket door system is the leading support of the pocket which has a side flange for the plasterboard to butt up against.
The intermediate jamb forms the rest of the pocket. The aluminium profile has a timber insert which provides extra strength and facilitates easy fixing.
The head channel for the Enigma pocket doors is the same width as the stud, making it simple to accurately place and fix to the head stud.
The leading edge and intermediate jambs slot into the base channel of the Enigma pocket door system and are fixed into place.
Manufactured by GEZE, the gear sets used in the Enigma pocket door system require almost no maintenance and are virtually silent, meaning doors slide open and closed without the difficulties sometimes caused by traditional hinges.
The standard sliding gear set is surface-mounted onto the top of the sliding door and is tested to EN 1527 1998 to 100,000 cycles.
The Enigma pocket door kit is constructed from aluminium. This material can be cut-to-size very simply using a standard carpenters chop saw to tailor to your specific size requirements.
The leading edge and intermediate jambs are slotted into the head channel and fixed into place once plumb.
The Enigma doorset has been fully fire tested to 30 minutes in single and double configurations.
Important note
To ensure the fire integrity is not compromised it is important that the wall partition is suitable and also the interface between the partition and doorset is correct.
At Enigma we are able to provide advice on the installation details so the appropriate regulations are met properly in conjunction with industry best practices, ensuring complete compliance.
The Enigma doorset has been acoustically tested and can be provided with the following ratings:
› 24dB
› 28dB
› 30dB
Please contact us on 020 3880 0339 where our Project Consultants would be glad to advise you further.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
574mm – 900mm ES 01
574mm – 900mm (Concealed NFR) ES 01C
900mm – 1290mm ES 02
900mm – 1290mm (Concealed NFR) ES 02C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
784mm – 1290mm ES 03
784mm – 1290mm (Concealed NFR) ES 03C
1290mm – 1450mm ES 04
1290mm – 1450mm (Concealed NFR) ES 04C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
The Enigma pocket door leaf can be ejected from the pocket quickly and easily thanks to the innovative Enigma touch latch with a single push of one leaf.
Order codes
130N Touch latch TL130
Virtually silent operation for use with double doors, when one leaf is activated the other follows suit in a seamless fashion.
In situations where you can’t fit the head of the pocket door directly to the building ceilings or floor slab and deflection tolerance is required, the Enigma system can be supplied with a self supporting head beam. This enables the head to be fitted, supporting up to 120kg.
If your door closes against a wall perpendicular to the door itself, a perpendicular wall jamb profile is provided to do away with the need to have a protruding nib.
The Enigma is fitted with a remote stop as standard, which allows you to adjust the back stop of the pocket door kit once the plasterboard is complete and the door leaf has been installed.
Full height, floor to ceiling Enigma doors give the ultimate open and spacious feel. The head of the pocket door kit along with the timber trims that carry the intumescent seals are set above the ceiling.
The Enigma pocket door system can be provided with an automated self closer. The closer is provided with infinite adjustment providing an extremely user friendly experience.
Satin stainless steel
Product code: ELS02
Satin stainless steel
60mm square – SFP01
Satin stainless steel
70mm diameter – CFP01
Satin stainless steel
135mm long – OFP01
Satin stainless steel
135mm long – RFP01
For complete freedom and the flexibility to integrate with any design scheme, the Enigma pocket door system can be ordered with or without a door leaf.
All Enigma door leafs are manufactured to the required size using a solid timber core with hardwood lippings on all 4 sides.
Once constructed, the doors are given cut-outs for sliding gear and (where required) a bottom guide channel so that they arrive on-site in a ‘ready to fit’ form.
For doors wider than 1220mm the door will be supplied in 2 sections to achieve the width. A jointing section will be supplied and a neat 3x3mm shadow gap.
As standard Enigma pocket doors are primed and ready to be painted on site.
A full range of RAL colours can be selected for the door leafs.
Extra durability can be added to the sliding pocket doors with a laminate coating.
If the design requires a veneer, choose from any timber style- it is then lacquered in a sheen of 30%.
The Enigma internal glass sliding doors are framed in timber. The frames are manufactured from solid hardwood steamed beech with a density of 720kg/m3 and is a fully FSC certified.
As standard, the timber door frame is provided to you pre-primed ready, meaning on-site painting in your chosen finish and colour can happen at once. Moreover, the frame can be constructed in differing species of timber and with different finishes, at your request. No architraves are included with the timber frame.
The Enigma pocket door system requires a simple wall build-up:
› 94mm stud
› 1 layer 12.5mm plasterboard either side
The strike jamb comes with rubber batwing seals to provide a seal when the door is closed.
The leading edge jamb of the Enigma pocket door system is the leading support of the pocket which has a side flange for the plasterboard to butt up against.
The intermediate jamb forms the rest of the pocket. The aluminium profile has a timber insert which provides extra strength and facilitates easy fixing.
The head channel for the Enigma pocket doors is the same width as the stud, making it simple to accurately place and fix to the head stud.
The leading edge and intermediate jambs slot into the base channel of the Enigma pocket door system and are fixed into place.
Manufactured by GEZE, the gear sets used in the Enigma pocket door system require almost no maintenance and are virtually silent, meaning doors slide open and closed without the difficulties sometimes caused by traditional hinges.
The standard sliding gear set is surface-mounted onto the top of the sliding door and is tested to EN 1527 1998 to 100,000 cycles.
The Enigma pocket door kit is constructed from aluminium. This material can be cut-to-size very simply using a standard carpenters chop saw to tailor to your specific size requirements.
The leading edge and intermediate jambs are slotted into the head channel and fixed into place once plumb.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
574mm – 900mm ES 01
574mm – 900mm (Concealed NFR) ES 01C
900mm – 1290mm ES 02
900mm – 1290mm (Concealed NFR) ES 02C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
Using a soft close dampener is the ultimate finish to the Enigma pocket door system.
Order codes
784mm – 1290mm ES 03
784mm – 1290mm (Concealed NFR) ES 03C
1290mm – 1450mm ES 04
1290mm – 1450mm (Concealed NFR) ES 04C
Important
Max door weight 80kg. This needs to be installed when fitting the track.
Virtually silent operation for use with double doors, when one leaf is activated the other follows suit in a seamless fashion.
In situation where you can’t fit the head of the pocket door directly to the building ceilings or floor slab and deflection tolerance is required, the Enigma system can be supplied with a self supporting head beam. This enables the head to be fitted, supporting 120kg.
If your door closes against a wall perpendicular to the door itself, a perpendicular wall jamb profile is provided to do away with the need to have a protruding nib.
The Enigma is fitted with a remote stop as standard, which allows you to adjust the back stop of the pocket door kit once the plasterboard is complete and the door leaf has been installed.
Enigma Motus is a powered pocket door that utilises a contactless electromagnetic propulsion system to silently open and close the sliding pocket door with no or minimal handling of the door itself. The visible frames are manufactured from solid hardwood steamed beech with a density of 720kg/m3 and is fully FSC certified and able to accept a wide range of architrave trims. Straightforward to install, Enigma Motus requires a simple wall build-up, which varies depending on fire rating:
NFR:
› 94mm stud
› 1 layer 12.5mm plasterboard either side
FD30:
› 94mm stud
› 2 layers of 12.5mm plasterboard either side
The strike jamb comes with rubber batwing seals to provide a seal when the door is closed.
As the Motus can be supplied as either non fire-rated or fire rated, this detail varies slightly. To see fire rated strike jamb please take a look at the FD30 solution.
The intermediate jamb forms the rest of the pocket. The aluminium profile has a timber insert which provides extra strength and facilitates easy fixing.
The intermediate jamb forms the rest of the pocket. The aluminium profile has a timber insert which provides extra strength and facilitates easy fixing.
The head channel for the Enigma pocket doors is the same width as the stud, making it simple to accurately place and fix to the head stud.
The leading edge and intermediate jambs slot into the base channel of the Enigma pocket door system and are fixed into place.
The Motus uses CS80-MAGNEO operater which requires almost minimal, or no, handling to activate and operates silently and smoothly.
The Enigma pocket door kit is constructed from aluminium. This material can be cut-to-size very simply using a standard carpenters chop saw to tailor to your specific size requirements.
The leading edge and intermediate jambs are slotted into the head channel and fixed into place once plumb.
Enigma Motus powered sliding door can be controlled in a number of ways depending on your application. See ‘Opening Options’ for further details.
The Motus Enigma doorset is fully fire rated to 30 minutes in single and double configurations.
Important note
To ensure the fire integrity is not compromised it is important that the wall partition is suitable and also the interface between the partition and doorset is correct.
At Enigma we are able to provide advice on the installation details so the appropriate regulations are met properly in conjunction with industry best practices, ensuring complete compliance.
The Enigma doorset has been acoustically tested and can be provided with the following ratings:
› 24dB
› 28dB
› 30dB
Please contact us on 020 3880 0339 where our Project Consultants would be glad to advise you further.
Virtually silent operation for use with double doors, when one leaf is activated the other follows suit in a seamless fashion.
Satin stainless steel
Product code:
ELS01 (NFR)
ELS02 (FD30)
Satin stainless steel
60mm square – SFP01
Suitable for NFR
Satin stainless steel
70mm diameter – CFP01
Suitable for NFR
Satin stainless steel
135mm long – OFP01
Suitable for NFR
Satin stainless steel
135mm long – RFP01
Suitable for NFR
For complete freedom and the flexibility to integrate with any design scheme, the Enigma pocket door system can be ordered with or without a door leaf.
All Enigma door leafs are manufactured to the required size using a solid timber core with hardwood lippings on all 4 sides.
Once constructed, the doors are given cut-outs for sliding gear and (where required) a bottom guide channel so that they arrive on-site in a ‘ready to fit’ form.
As standard Enigma pocket doors are primed and ready to be painted on site.
A full range of RAL colours can be selected for the door leafs.
Extra durability can be added to the sliding pocket doors with a laminate coating.
If the design requires a veneer, choose from any timber style- it is then lacquered in a sheen of 30%.
The standard method; simply nudge the door open or closed and Motus will assist with the rest.
The sensor is fitted to the wall and by simply moving your hand in front of the sensor this activates the door.
Fixed to the wall, the button is pressed to activate opening. Push button can be provided as a hard wired or wireless option.
Available alongside the wireless push button the hand-held transmitter enables remote opening of the door.
Select your pocket door size
Important installation note
When using door heights of 2300mm+ then it is recommended the wall is double boarded. If using 2 layers of 12.5mm plasterboard then add (145) to the product code to specify this.
Visible Trim – Specifications
Can’t find the size you need? Go bespoke;
Email your enquiry to sales@enigmapocketdoors.com